91
on: December 13, 2020, 06:41:56 PM
|
||
Started by NicNac337 - Last post by NicNac337 | ||
Thanks!
|
92
on: December 13, 2020, 12:45:37 PM
|
||
Started by NicNac337 - Last post by 52 Ruhe | ||
93
on: December 13, 2020, 12:19:37 PM
|
||
Started by NicNac337 - Last post by NicNac337 | ||
Looking for 2008-2016 Yamaha YZF R6 gas tank (pump not needed).
Would like one with two less dents than my current one which has matching dents on either side ![]() |
94
General Category / New Member Introductions / Re: Lots of questions (was: Coming back after fifteen years...)
on: December 07, 2020, 06:28:18 PM
|
||
Started by JustAnotherSquid - Last post by realpsi | ||
I have a Ram stem mount and it moves quite a bit. Even the directions tell you it will move. For a 360 camera reframing this won't be a problem, but for a GoPro style the movement might be an issue.
|
95
General Category / New Member Introductions / Re: Lots of questions (was: Coming back after fifteen years...)
on: December 07, 2020, 11:42:56 AM
|
||
Started by JustAnotherSquid - Last post by JustAnotherSquid | ||
Thanks Monkeyman, I just ordered one of those cheap clear cases from Amazon and will set it up as you described.
|
96
General Category / New Member Introductions / Re: Lots of questions (was: Coming back after fifteen years...)
on: December 07, 2020, 05:50:53 AM
|
||
Started by JustAnotherSquid - Last post by MonkeyMan | ||
I'd recommend drilling the GoPro camera case just at base, just above where the screw passes through to attach the case to the mount. I've done that with all of my cases, using an 1/8" drill bit and going slowly so it doesn't turn into a mess. Then use safety wire to wire it to a fixed mount - either the triple clamp itself or something on the triple that has been drilled and wired.
I'd also recommend lowering the RAM mount so the camera is closer to the key. Sure, right now it might not be in the way but as you get more proficient you might find the camera limiting your ability to get your head down....or at least being a limiting factor. Get the camera out of the way now and you'll remove a future 'obstacle' to improvement. And don't worry, with the wide field of view of these fisheye lenses you won't miss anything. In fact, you might just pick up a little more of the dash which might also be useful as a learning tool (RPM range, speed, etc) Best of luck with the continued modifications to make that GSXR750 yours and looking forward to the 2021 season! |
97
General Category / New Member Introductions / Lots of questions (was: Coming back after fifteen years...)
on: December 06, 2020, 04:57:18 PM
|
||
Started by JustAnotherSquid - Last post by RocketDan | ||
You will need to run some safety wire from the actual camera to the triple clamp. Something that keeps the camera from flying down the track should the bolt holding it to the mount comes loose.
You are smart to ask these questions ahead of time. Having to take your bike through tech multiple times is no fun. Daniel Hughes 2015 R1 |
98
General Category / New Member Introductions / Re: Lots of questions (was: Coming back after fifteen years...)
on: December 06, 2020, 04:22:09 PM
|
||
Started by JustAnotherSquid - Last post by JustAnotherSquid | ||
Oh, and before anyone objects, the mount does not block your view of the instruments. Here's a picture taken from the riders point of view with the GoPro mounted. You can't even see it in your field of view.
![]() |
99
on: December 06, 2020, 12:27:20 PM
|
||
Started by JustAnotherSquid - Last post by JustAnotherSquid | ||
RocketDan, thank you for all of your help. I am grateful for this forum, and for the opportunity to get good answers before showing up at the first track day.
![]() Question #4 of 87000: ![]() Following the recommendation of a guy on the WERA forums, I got this RAM steering-stem mount for the Gixxer. This mount is pretty solid and I am confident that it is not going anywhere. Having said that, will it pass tech? If not, what else needs to be done to secure the camera? ![]() ![]() ![]() |
100
on: December 02, 2020, 03:42:32 PM
|
||
Started by boike333 - Last post by boike333 | ||
I have a very clean 2006 SV650 for sale. 22000 miles. It has an M4 exhaust. Other than that its pretty much stock. Three sets of tires go with it (Q3+/Road 5's/Contis.
$3250 Cant post pics for some reason so PM and ill text them over if your interested. Matt |